#Star wars rey cosplay beach install

Sensible.Ĭosplay, that pinnacle of performative fandom, dates back to the mid-20th century some accounts note that there were cosplayers at the first World Science Fiction Convention, in 1939. It's 2019's Comic-Con International, and compared to the wizards and warlocks and Wonder Women crowding the floor, the outfit of the Jedi Rey is plain, simple. “It's been falling down all day.” With an assist by her mom, the 17-year-old finally twists and tucks her costume into place. “We're having issues here,” she says, with an exasperated giggle. The cavernous hall is 460,000 square feet, and McIntosh is taking up about three of them, trying to cinch the beige bandages wrapped around her arms. She's surrounded by massive signs with corporate logos, from Nintendo to DC Comics. People in comic-book tees are rushing past her, lit up by too-bright fluorescents. Once you're set, use an almond paint to finish out the strap connectors.Annamarie McIntosh is coming undone. Don't be like me-if you're using vinyl, make sure to prepare the vinyl with PlastiDip first, or the paint won't cure correctly. When the two strap attachments are complete, mask off the buttons with painter's tape and spray paint the leather/vinyl. Things should look like a capital H when you're done. Use the smaller pieces of leather to bridge the gap and form a loop as you sew or glue each pair of snaps together.

#Star wars rey cosplay beach install

Install the snaps into each side of the four strips, using the instructions on the box, making sure that you've installed them correctly so that they can snap when wrapped around the conduit. Cut a few additional small pieces for attaching the pieces together and creating a small loop for the buckle.

You can do this!Ĭut four small rounded strips of leather of vinyl that are long enough to wrap around the conduit and overlap about a half inch. This is probably the most challenging part of the build, but it's really not that difficult. Now you're ready to attach the main shaft. As mentioned above, drilling through this section might be preferable. In the end, I drilled four holes through the wheel area back into the sink handle and installed four long screws to keep things secure. I added electrical tape to hold things together (which I left on the staff - I don't recommend you do this), but it still didn't want to hold together. The large wheel turned out to be the most difficult piece to keep attached, and despite ample amount of superglue and hot glue, I had a difficult time keeping things together. You can also use circles cut out of wood or wooden pieces from a hobby store to do the same thing. I completed this top section by adding round plastic wheels of different sizes to the top and bottom of the third Danco handle. (Alternatively, you could drill through the next section with a 1/2' bit to keep the conduit in one piece to increase stability.) Next, I cut a 4' piece of conduit and attached it to the connector piece with hot glue. Now, you can glue the outer piece of the connector to the bottom of the sink handle for both the top and bottom of the staff. Now, that you've got your stuff, let's build this thing! Step 2: Working on the End Pieces (This build uses some materials recommended in a post I came across on the RPF.) I think that's a great idea, and I will probably add that to the staff I built for my wife. I've also had someone comment that they used a dowel rod inside of the plastic conduit to make the staff more rigid.

Some fabric scraps for the middle section.

A piece of canvas that's 4' x 45' or a 45' strap.

Some scraps of leather or vinyl for the places where the strap attached to the staff.Small scraps of about 2/16' wood or PVC board for some small details.

25' or so thick cord for the ends of the handles. Some fairly thick coated wire for the details on the handles.Danco Vice Grip Acrylic Handles (3 handles - 2 sets of 2 at $10.90 each).Southwire 1/2' Liquidtite Connector (2 of these at $2.06 each).1/2' conduit in a 10' length (1 of these for $2.30) I used plastic conduit, but I wish I had used metal.1-Spray 2' Showerhead in White (2 of these at $1.97 each).Here's a fairly comprehensive list of everything you'll need to build this staff, most of which you can pick up at Home Depot: